- phenixbb - phenix-online.org

Test
by Paul Adams 05 Mar '15

05 Mar '15

Test of restored Mailman system. Please ignore. -- Paul Adams Deputy Division Director, Physical Biosciences Division, Lawrence Berkeley Lab Division Deputy for Biosciences, Advanced Light Source, Lawrence Berkeley Lab Adjunct Professor, Department of Bioengineering, U.C. Berkeley Vice President for Technology, the Joint BioEnergy Institute Laboratory Research Manager, ENIGMA Science Focus Area Building 64, Room 248 Building 80, Room 247 Building 978, Room 4126 Tel: 1-510-486-4225, Fax: 1-510-486-5909 http://cci.lbl.gov/paul Lawrence Berkeley Laboratory 1 Cyclotron Road BLDG 64R0121 Berkeley, CA 94720, USA. Executive Assistant: Louise Benvenue [ LBenvenue(a)lbl.gov ][ 1-510-495-2506 ] --

1 0

get_cc_mtz_pdb for neutron data table
by Maxime Cuypers 26 Feb '15

26 Feb '15

hi, i need the correlation coefficients map/residues for a publication, which command should i use to get phenix.get_cc_mtz_pdb to take into account the neutron scattering tables? seems it uses the x ray tables by default. i can not find it on this page: http://www.phenix-online.org/version_docs/1.8.3-1472/get_cc_mtz_pdb.htm#anc… many thanks for your reply. -- Dr. Maxime Cuypers

2 1

hiding clash dots
by Sebastiano Pasqualato 26 Feb '15

26 Feb '15

Hi all, a quick question: how do I get rid of the clash dots that appear in Coot, when opened from a phenix job? thanks a lot in advance, best, Sebastiano -- Sebastiano Pasqualato, PhD Crystallography Unit Department of Experimental Oncology European Institute of Oncology IFOM-IEO Campus via Adamello, 16 20139 - Milano Italy tel +39 02 9437 5167 fax +39 02 9437 5990 web http://is.gd/IEO_XtalUnit <http://is.gd/IEO_XtalUnit>

3 3

on phenix.cut_out_density
by Smith Lee 26 Feb '15

26 Feb '15

Dear All, Can the mtz file produced by phenix.cut_out_density be used by Phenix refine for refinement? Smith

2 1

a sharp rise of R-free in resolution bin
by Singh, Bishal 25 Feb '15

25 Feb '15

Hello everyone, I am refining a structure at 2.3 A resolution. R-work/R-free is 26/31 and is not reducing further. When I looked into the resolution bin, I notices a sharp rise of R-free between resolution range 2.5-2.6 A (marked in figure below). However R-work is fine. I am doubtful of reducing the resolution to 2.5 A or lower. Please suggest me your opinion. Your words will be highly appreciated. With regards, Bishal Singh PhD Student University of Heidelberg, Germany

2 1

How to define a disulfide bond between symmetry related molecules in phenix.refine
by Michael Hothorn 25 Feb '15

25 Feb '15

Dear all, I am trying to refine an intermolecular disulfide bond in phenix.refine. The disulfide involves Cys 188 in chain A and Cys 188 of chain B of a symmetry related molecule, with symop -X, Y+1/2, Z+1/2. There are two molecules in the AU, SG is P212121. I generated the following SSBOND entry in the pdb header: SSBOND 2 CYS A 188 CYS B 188 1555 3555 2.04 Based on this: http://www.wwpdb.org/documentation/file-format/format33/sect6.html the format seems fine, but the disulfide is not being recognized during refinement. Could someone point out to me how to correctly define this for phenix.refine. Thanks! Michael

3 2

sharp rise of R-free in resolution bins
by Singh, Bishal 25 Feb '15

25 Feb '15

Hello everyone, I am refining a structure at 2.3 A resolution. R-work/R-free is 26/31 and is not reducing further. When I looked into the resolution bin, I notices a sharp rise of R-free between resolution range 2.5-2.6 A (marked in figure below). However R-work is fine. I am doubtful of reducing the resolution to 2.5 A or lower. Please suggest me your opinion. Your words will be highly appreciated. With regards, Bishal Singh PhD Student University of Heidelberg, Germany

1 0

On Ramachandran restraints of Phenix refine
by Smith Lee 25 Feb '15

25 Feb '15

Dear All, If my resolution was between 2.5-3.0 A, and if I did not use Ramachandran restraints in the Phenix refine the Ramachandran outliers would be increased significantly during the refinement process, in this situation may I use Ramachandran restraints in the Phenix refine? I am looking forward to getting your reply. Smith

2 1

Bug? phenix.hyss crashes on reading CNS def file
by Mark A Saper 23 Feb '15

23 Feb '15

I am trying the example described on this documentation page: http://www.phenix-online.org/download/documentation/cci_apps/hyss/examples.… For mbp.hkl the HySS command suggested is: phenix.hyss $CNS_SOLVE/doc/html/tutorial/data/mbp/mbp.hkl 4 yb —symmetry $CNS_SOLVE/doc/html/tutorial/data/mbp/def The software does not expect the “{“ character in the def file. I can send you the Traceback on request. I am running dev-1951. -Mark

1 0

on TLS for Phenix refine
by Smith Lee 22 Feb '15

22 Feb '15

Dear All, For TLS, the document says, "Can I use both TLS and anisotropic ADPs? Yes, but not for the same atoms - since TLS is essentially constrained anisotropic refinement, the two methods are mutually exclusive". In the "Refinment settings" of the Phenix refine graphical interface, will you please tell me which button is for the anisotropic ADP? The individual B-factors, or the Group B-factors, or only the "Optimize X-ray/ADP weight"? I am looking forward to getting your reply. Smith

3 2